Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 0
  • *Guests: 29
  • *Total: 29

Author Topic: Wooden overhead frame  (Read 650 times)

Offline Jimmerrelie

  • CockpitBuilder
  • *
  • Posts: 13
  • Karma: +0/-0
  • Cockpit builder
  • First Name: Jim
  • Home Location: Auburn, NY
Wooden overhead frame
« on: November 19, 2017, 10:36:35 AM »
Hi everyone. I started my new overhead frame today. I was planning on using 3/4" By 3 1/2" boards that I reclaimed from another project, but as i look at the panels on the boards, they seem too wide. I am wondering what size lumber others have used.
 Also any tips on putting this thing together would be greatly appreciated.  Thanks guys.        Jim
I7 4770k oc to 4.2
MSI mpowerMax mobo
Gtx  780sc
16g ripsaw ram
Fsx w/ acceleration boxed
Ifly 737ng CBE

Offline Bob Reed

  • Administrator
  • I am chained to this website!
  • *
  • Posts: 2,181
  • Karma: +10/-0
  • Bob the Builder!
  • First Name: Bob
  • Home Location: Holley, New York
Re: Wooden overhead frame
« Reply #1 on: November 19, 2017, 12:26:57 PM »
You will need something a little thinner. More so keep in mind that there will be hardware on the under side of those panels so make sure whatever you use for rails does not get in the way of that. You will have to tinker to get the right size.

Offline FredK

  • Forum GURU
  • *
  • Posts: 386
  • Karma: +0/-0
  • 737NG Cockpit Builder
  • First Name: Fred Kurasiewicz
  • Home Location: Williamsburg, Virginia, USA
Re: Wooden overhead frame
« Reply #2 on: November 19, 2017, 12:45:53 PM »
3/4 inch premium pine worked for me.  No clearance issues for hardware.....that includes a full set of Flight Illusion gauges which I have mounted.

I would advise that you use premium grade furniture quality wood. You need to have everything lay perfectly flat and without any bowing etc.  Take your time and be precise with your spacing measurements and you will do fine.

Fred K
« Last Edit: November 19, 2017, 12:50:26 PM by FredK »
Boeing 737NG-800, Prepar3D v3.35, Sim-Avionics, WideView multi-channel (curved screen), Optoma 1080GT projectors (3), Fly Elise warping, FSGRW weather, FDS OH panels and CDUs, SimParts MIP, FDS SysBoards (OH), CPFlight MCPPro and pedestal panels, FI Gauges, converted motorized TQ (SIOC), Weber seats

Offline navymustang

  • Simulation Engineer
  • Forum GURU
  • *
  • Posts: 274
  • Karma: +0/-0
  • Building a 737-800 full scale cockpit
  • First Name: Jim
  • Home Location: Orlando, FL
Re: Wooden overhead frame
« Reply #3 on: November 19, 2017, 03:33:22 PM »
How about making the outside frame of wood and using angled aluminum for the rails, would give you much more flexibility.
Building a full scale 737-800 AATD for home use. Majority of hardware is from Sismo Solutions, software is Prosim under P3D.
Please note that I am a self-employed professional cockpit builder that provides consulting to defense contractors and civilian schools and airlines.

Offline Jimmerrelie

  • CockpitBuilder
  • *
  • Posts: 13
  • Karma: +0/-0
  • Cockpit builder
  • First Name: Jim
  • Home Location: Auburn, NY
Re: Wooden overhead frame
« Reply #4 on: November 19, 2017, 08:26:20 PM »
Hi. Thanks guys for the tips. The wood I have is general lumber and definitely not suited for this build. Off to Lowe's tomorrow  for some high grade stuff. As for the aluminum rails, that sounds like a good idea. I'll have to look into it. Just don't know how I would fasten the rail to the wood.
I7 4770k oc to 4.2
MSI mpowerMax mobo
Gtx  780sc
16g ripsaw ram
Fsx w/ acceleration boxed
Ifly 737ng CBE

Offline ifeliciano

  • Forum GURU
  • *
  • Posts: 56
  • Karma: +0/-0
  • Aviation Enthusiast
  • First Name: Ivan
  • Home Location: Arlington, Texas
Re: Wooden overhead frame
« Reply #5 on: November 20, 2017, 12:54:17 PM »
Please have in mind that the "high grade" wood does not necessarily mean is straight and free of bowing and cupping. It relates to the quality of the surface. Basically free of knots and any damage. You will need to inspect it for straightness.

I would suggest you find a good lumber supply for your wood. Some offer jointing and planning for a small fee. If you break it down to board foot, you'll see how Lowes and/or HD charge a crazy amount of money for their S4S wood.

I agree with Jim, in making a wood outer frame and angle aluminum or aluminum t-bar, if you find the right size, for the rails.



Offline jackpilot

  • Moderator
  • I am chained to this website!
  • *
  • Posts: 3,720
  • Karma: +37/-0
  • 737-800 Sim-Avionics/Full Cockpit FDS + OEM P3D V4
  • First Name: Jack
  • Home Location: Montreal / Canada
Re: Wooden overhead frame
« Reply #6 on: November 20, 2017, 02:13:39 PM »
My 2 cents, from experience

Wood  has to be kept to a minimum and limited to large structural parts if no other material can do.

Thickness is always an issue and an OVH requires very tight adjustments that wood does not allow.
Before going to  real frames, I used to build my own, exclusively with aluminum.
Much better results and weight than a bulky wood contraption.
Here is a pic of my previous AftOVH if it can help.
L section rails for the perimeter, T section for the inside dividers.

« Last Edit: November 20, 2017, 02:16:26 PM by jackpilot »


Jack

Offline navymustang

  • Simulation Engineer
  • Forum GURU
  • *
  • Posts: 274
  • Karma: +0/-0
  • Building a 737-800 full scale cockpit
  • First Name: Jim
  • Home Location: Orlando, FL
Re: Wooden overhead frame
« Reply #7 on: November 20, 2017, 02:37:38 PM »
Jim, don't be afraid of working in all aluminum. It bolts together very easy, better than wood. And don't forget rivets.
Better yet, go to Harbor Freight and get their low cost RivNut tool. These RivNuts are incredible and I use them in my professional building all the time.
www.harborfreight.com/45-piece-threaded-insert-riveter-kit-1210.html

Building a full scale 737-800 AATD for home use. Majority of hardware is from Sismo Solutions, software is Prosim under P3D.
Please note that I am a self-employed professional cockpit builder that provides consulting to defense contractors and civilian schools and airlines.

Offline MistyBlue

  • Forum GURU
  • *
  • Posts: 67
  • Karma: +1/-0
  • Aviation Enthusiast
  • First Name: Tony
  • Home Location: Texas
Re: Wooden overhead frame
« Reply #8 on: November 20, 2017, 02:41:05 PM »
I went with 3/4" square Aspen (I think) dowel from Home Depot.  Anything less and I found there wouldn't be enough space to screw two panels side by side without breaking through the sides of the wood or leaving it weakened. 

I did have some clearance issues with some panel screws and switches so I used a Dremel to cut into areas that needed the extra spacing.   

Glued everything with 2 part 6 min epoxy.  It's quite solid.

Once I had the frame properly pieced together I fit it to my FDS overhead frame, shimmed both sides, and made sure it was properly placed then drilled the mounting holes.  Then, I put everything into the overhead.  It got a LOT heavier really quick.  Kinda surprised me.

I haven't mounted the completed overhead yet so my fingers are crossed that it still goes in ok and holds up well.  Definitely a two person operation to pu in.

If I were to do it again, I would do it all aluminum like Jack recommends.  Stronger, lighter, thinner, etc.  I just went with the tools I had on hand which were all wood working tools.

EDIT:  I agree with the earlier comment about warped wood.  I spent a lot of time going through Home Depot supplies (now that I think of it, it was Lowes) making sure I had the straightest pieces I could find.  There were a lot of bowed pieces.  Even a slight bow will create a lot of headaches.
« Last Edit: November 20, 2017, 02:48:43 PM by MistyBlue »
Tony
My Never Ending 737 Sim
http://www.mynesim.com

Offline Jimmerrelie

  • CockpitBuilder
  • *
  • Posts: 13
  • Karma: +0/-0
  • Cockpit builder
  • First Name: Jim
  • Home Location: Auburn, NY
Re: Wooden overhead frame
« Reply #9 on: November 20, 2017, 08:49:22 PM »
Thanks guys. Feeling inspired now. I'm thinking about 1/2 inch oak for the outer frame with  3/4 inch aluminum rails for the spars. Thanks for the great pics, they'll make a good guide as I progress.
I7 4770k oc to 4.2
MSI mpowerMax mobo
Gtx  780sc
16g ripsaw ram
Fsx w/ acceleration boxed
Ifly 737ng CBE

 

COUNTDOWN TO WF2018


WORLDFLIGHT TEAM USA

Will Depart in...

Recent Posts

Jetmax 737 TQ for Sale
by Holclo
[Today at 03:11:42 AM]
So this thing is on it's way....
by iwik
[Today at 12:50:45 AM]
B747-400 Update - Oxygen Masks done ...
by jackpilot
[December 17, 2017, 06:48:04 PM]
Shell MIP Move
by Ed
[December 17, 2017, 06:17:47 PM]
Sismo modules shut down with P3D 4.1 and WideTraffic/WideView 64
by FredK
[December 17, 2017, 06:14:54 PM]
I want your feedback!
by Trevor Hale
[December 17, 2017, 12:59:38 PM]
CraigSim 737 update
by Caflyt
[December 17, 2017, 05:59:58 AM]
737 Document Holder
by Aerosim Solutions
[December 16, 2017, 09:30:22 PM]
My Simming Year in Review
by Aerosim Solutions
[December 16, 2017, 09:08:04 PM]
Wanted: parts of yoke
by gufau
[December 16, 2017, 04:36:13 AM]
Upgrading my PC. Will this work?
by Caflyt
[December 15, 2017, 04:23:09 PM]
737-800 Arduino X-Plane Build
by kurt-olsson
[December 15, 2017, 12:45:44 PM]
Weather set problem
by luisgordo
[December 15, 2017, 09:25:08 AM]
Mickey's Flightdeck - A Boeing 737-800 Cockpit on Youtube
by B747-400
[December 15, 2017, 06:21:29 AM]
Lian Li Purchase?
by ifeliciano
[December 15, 2017, 01:17:30 AM]
WANTED: Real 737 Dual Linked Yokes
by bernard S
[December 14, 2017, 04:23:52 PM]
Older USB CPFlight MCP for sale
by jr2mey
[December 13, 2017, 08:35:25 AM]
RAL 7011 - Paint Options
by GarethH
[December 13, 2017, 08:20:51 AM]
Sismo IRS Panel - Anyone Have One?
by blueskydriver
[December 13, 2017, 08:01:17 AM]
737 control columns Capt & FO
by Joe Lavery
[December 13, 2017, 06:14:31 AM]
Gas strut newton for elevation
by Trevor Hale
[December 11, 2017, 05:11:30 PM]
MIP Dimmer Panels
by ifeliciano
[December 11, 2017, 01:51:13 PM]
New supplier for your sim
by Fcoq
[December 11, 2017, 02:59:18 AM]
Got My Flightdeck Solutions Oxygen Panels...
by blueskydriver
[December 10, 2017, 12:35:54 AM]
737 Aft Overhead EEC Switches - Where do I get one?
by MistyBlue
[December 09, 2017, 01:53:43 PM]
P3D v3 Verus P3D V4 ?
by Bob Reed
[December 09, 2017, 09:39:42 AM]
Boeing 737-800 Next Generation Simulator
by fsaviator
[December 09, 2017, 07:59:51 AM]
PFC Jetliner Column Yoke USB -SOLD-
by blueskydriver
[December 08, 2017, 06:46:26 PM]
Interfacing BENDIX/KING KMD-150 GPS and X-Plane
by RayS
[December 07, 2017, 07:56:39 PM]
Question for those that have converted real TQs
by kurt-olsson
[December 07, 2017, 04:50:44 PM]