Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 2
  • *Guests: 50
  • *Total: 52

Author Topic: Need help: Teensy 3.5 not working where 3.2 is.  (Read 335 times)

Offline ElStino737

  • Forum GURU
  • *
  • Posts: 22
  • Aviation Enthusiast
  • First Name: Stijn
  • Home Location: Ninove
Need help: Teensy 3.5 not working where 3.2 is.
« on: February 10, 2017, 10:23:08 AM »
So far I was using Teensy 3.2 to interface my panels to xplane with no real problems.
Today I tried a 3.5 and I'm hitting a problem I can't get my head around.

Whenever I ask for an output (eg a Korry through a ULN2803A) based on an xplaneref, the program freezes and stops communicating to Xplane.
Asking for an output not based on xplaneref is fine though.
When I change the board out to a 3.2 in the same setup, all works fine.
I tried 2 different 3.5's, same problem.

Is there some fundamental difference between the 2 that can be causing this?


Offline RayS

  • I may as well be Staff!
  • *
  • Posts: 590
  • Private Pilot, Sim Enthusiast
    • Anthony Scott Photography
  • First Name: Ray Sotkiewicz
  • Home Location: Seattle, WA
Re: Need help: Teensy 3.5 not working where 3.2 is.
« Reply #1 on: February 10, 2017, 12:36:25 PM »
Dumb question: Did you change the board type in your dev environment? I'm not sure what the board types are in the dev app, but that might be it.
Ray Sotkiewicz

Offline ElStino737

  • Forum GURU
  • *
  • Posts: 22
  • Aviation Enthusiast
  • First Name: Stijn
  • Home Location: Ninove
Re: Need help: Teensy 3.5 not working where 3.2 is.
« Reply #2 on: February 10, 2017, 02:20:56 PM »
Dumb question: Did you change the board type in your dev environment? I'm not sure what the board types are in the dev app, but that might be it.


Yes, I did.
It doesn't let you upload the sketch if you don't.

 

Recent Posts

New AFT OVH
by fsaviator
[April 23, 2017, 08:13:39 PM]
Oasis 737 Project
by 737NGer
[April 23, 2017, 04:52:24 PM]
Engravity glarewings set for sale
by scojj
[April 23, 2017, 06:00:01 AM]
CPFlight MIP board
by scojj
[April 23, 2017, 05:57:42 AM]
CPFlight MIP737ICS and project magenta : gauges issue.
by scojj
[April 23, 2017, 05:54:18 AM]
Life of a Veteran Airplane
by iwik
[April 22, 2017, 04:09:57 PM]
Boeing 737NG parts: OVH, MIP and Yoke
by rtopinka
[April 21, 2017, 06:41:23 PM]
SEP/MEP 3DOF motion simulator for sale
by rtopinka
[April 21, 2017, 05:09:36 PM]
Cockpit Parts
by goirishgo1083
[April 20, 2017, 02:52:50 PM]
Rotary with a button
by Atomic_Sheep
[April 19, 2017, 11:49:52 PM]
737NG Single Seat Trainer "Starter Kit" :-)
by blueskydriver
[April 19, 2017, 10:43:37 PM]
X-Plane 11 multi-monitor & Fly Elise-ng - tuto
by pierrevw
[April 18, 2017, 05:48:32 PM]
KIng Air yokes
by RayS
[April 18, 2017, 05:40:03 PM]
I Need A Particular Photo.......
by FredK
[April 17, 2017, 03:05:10 PM]
Looking for FDS G2 EFIS Unit
by Trevor Hale
[April 17, 2017, 02:56:23 PM]
737 Overhead frame.
by kurt-olsson
[April 17, 2017, 01:17:07 PM]
B737 Startswitches
by airupthere
[April 17, 2017, 11:10:19 AM]
737 MIP captains side
by MrMikaelEricsson
[April 17, 2017, 02:37:18 AM]
10.4 LCD Source?
by rprather
[April 16, 2017, 08:08:50 PM]
Captain Joe Videos...very informative!!!
by Flying_Fox
[April 16, 2017, 05:39:04 PM]
Boeing 737 700/800 QRH
by bernard S
[April 15, 2017, 04:25:53 PM]
Phidgets Advanced Servo 8-Motor Card
by pierclav
[April 14, 2017, 11:12:41 PM]
XML lvars & LEDs
by jmcmanna
[April 14, 2017, 10:03:48 AM]
Could anyone use this 757 TQ stand??
by bernard S
[April 14, 2017, 09:02:02 AM]
Open Cockpit Radios: Tuning frequency from ATC programs ?
by brianwilliamson
[April 13, 2017, 08:53:28 PM]
Wanted: 737 MIP Captain side
by MrMikaelEricsson
[April 13, 2017, 11:51:35 AM]
GoPro
by Bob Reed
[April 12, 2017, 10:18:40 PM]
Correct B737 MIP dimensions?
by MrMikaelEricsson
[April 12, 2017, 02:16:11 PM]
My adaptation to Saitek's real-scale Embraer Phenom 100 or 300!
by eduardohbm
[April 12, 2017, 01:39:47 PM]
New member
by Fcoq
[April 12, 2017, 06:09:42 AM]