Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 0
  • *Guests: 49
  • *Total: 49

Our Discord

Author Topic: First 3D Print HOORAY!  (Read 1003 times)

Offline blueskydriver

  • I am chained to this website!
  • *
  • Posts: 1,664
  • Karma: +4/-2
  • FSX/FS9 PM, PMDG737-700, FDSMIP/Overhead.etc
  • First Name: John
  • Home Location: WI
First 3D Print HOORAY!
« on: February 10, 2018, 02:01:41 PM »
Hey Everyone,

This past week I printed my first 3d printer object on my CR-10S. It was the notorious little cat, but I used Simplify 3D software and not CURA. It went well until to the very last 2 mins to go, and then the cat came unstuck. However, the printing is still a success because I used the cheap tape that was included in the box on the glass plate, so I blame that.

My plan is to buy some new glass plates and then try the sanding/scufffing them up trick that others are doing well with...

In the mean time, I think it's time we start a 3d printing section for cockpit builders and cockpit parts, and I ask for Trevor (yep, you buddy) to start talking...lol! Tell us what your experiences are for the cockpit parts, plus hints or insights. Also, Bob I know you're sitting on a 3d printer too, so start talking buddy; lets here your thoughts as well.

Heck, maybe make some videos or a live video on twitch (or YouTube), just about cockpit parts. Bob I know you like doing live feeds, so setup and do a few, you can time-lapse the actual print time(s)...

John
| FSX | FDS-MIP OVRHD SYS CARDS FC1| PM | PMDG 737-700 | UTX | GEX | UT7 | ASE | REX2 | AES | TSR | IS | TOPCAT | AvilaSoft EFB | OC CARDS & OVRHD GAUGES| SIMKITS | SW 3D Lights | FS2CREW2010 | FSXPassengers | Flight1 AE | MATROX TH2GO-D | NTHUSIM | 3-Mits EW230Ust Proj |

Offline Bob Reed

  • Administrator
  • I am chained to this website!
  • *
  • Posts: 2,345
  • Karma: +11/-0
  • Bob the Builder!
  • First Name: Bob
  • Home Location: Holley, New York
Re: First 3D Print HOORAY!
« Reply #1 on: February 10, 2018, 02:11:58 PM »
I do have a number of good time lap videos for some of my prints. I will give that some thought since I do have a Twitch channel already. I have printed a bunch of stuff.. The printer is running right now. A 3D printer is simply a must for a cockpit builder. I do not see how I ever survived with out it. Things you would never think of, like, I needed some stand offs to put my interface cards in the sim.. So instead of looking all around and then order them, I went into TinkerCad and drew then and then to the printer they went. Need a bracket, print it... It has saved me a lot of time, head aches and money!

Offline fsaviator

  • I am chained to this website!
  • *
  • Posts: 1,263
  • Karma: +2/-0
  • Aviation Enthusiast
    • Boeing 737 Next Generation Simulator
  • First Name: Warren
  • Home Location: Riverview, Florida
Re: First 3D Print HOORAY!
« Reply #2 on: February 11, 2018, 11:00:28 PM »
John,
I found that hairspray on the glass does a good job of ensuring the print sticks.
Also, I also found that running three or four loops around the perimeter gets the nozzle flowing evenly before it starts the print.
Warren "MTN385"
Florida

http://www.B737NG-SIM.com and https://www.facebook.com/fsaviator on facebook
FSX, Prosim737 Suite, FDS DSTD 2.0 MIP, RevSim Proline TQ, ACE Dual-linked Yokes, Intel 3.5GHz i7-3770K, MSI Z77A-G45, 16GB G.Skill TridentX DDR3-2400, Galaxy GTX670 GC 4GB, OCZ 60GB Vertex 3

Offline Trevor Hale

  • Administrator
  • I am chained to this website!
  • *
  • Posts: 3,551
  • Karma: +22/-0
    • Cockpitbuilders.com
  • First Name: Trevor
  • Home Location: New Liskeard, Ontario
Re: First 3D Print HOORAY!
« Reply #3 on: February 12, 2018, 07:03:58 AM »
I have a sheet of PEI on top of my borosilicate glass, gone is the need for Glue, Hairspray, tape or anything else.  As the plastic heats it gets stickier, when the part cools, the PEI will release.  Depending on how much you push the plastic into the bed though, sometimes it can be a real tough job getting the part off.

In my opinion, PEI is the only way to go.

Trev
Trevor Hale

Owner
http://www.cockpitbuilders.com

Director of Operations
Worldflight Team USA
http://www.worldflightusa.com

VATSIM:

Offline fsaviator

  • I am chained to this website!
  • *
  • Posts: 1,263
  • Karma: +2/-0
  • Aviation Enthusiast
    • Boeing 737 Next Generation Simulator
  • First Name: Warren
  • Home Location: Riverview, Florida
Re: First 3D Print HOORAY!
« Reply #4 on: February 12, 2018, 07:54:00 AM »
I'll look into it Trevor.  Thanks!
Warren "MTN385"
Florida

http://www.B737NG-SIM.com and https://www.facebook.com/fsaviator on facebook
FSX, Prosim737 Suite, FDS DSTD 2.0 MIP, RevSim Proline TQ, ACE Dual-linked Yokes, Intel 3.5GHz i7-3770K, MSI Z77A-G45, 16GB G.Skill TridentX DDR3-2400, Galaxy GTX670 GC 4GB, OCZ 60GB Vertex 3

Offline Trevor Hale

  • Administrator
  • I am chained to this website!
  • *
  • Posts: 3,551
  • Karma: +22/-0
    • Cockpitbuilders.com
  • First Name: Trevor
  • Home Location: New Liskeard, Ontario
Re: First 3D Print HOORAY!
« Reply #5 on: February 12, 2018, 08:13:56 AM »
I'll look into it Trevor.  Thanks!


Just have to bring your bed temperature up about 3-5 degrees higher to make sure the PEI is at temp before you start printing.  With Buildtac I would run 60 degrees bed with Pla with the PEI and glass I run at 63 degrees C.


Trev
Trevor Hale

Owner
http://www.cockpitbuilders.com

Director of Operations
Worldflight Team USA
http://www.worldflightusa.com

VATSIM:

Offline iwik

  • Forum GURU
  • *
  • Posts: 327
  • Karma: +0/-0
  • GA Jockey
  • First Name: Les
  • Home Location: Christchurch New Zealand
Re: First 3D Print HOORAY!
« Reply #6 on: February 12, 2018, 10:49:57 AM »
Trev's right,PEI sheet is the way to go. I've got a Prusa I3 Mk2 and it uses a PEI sheet.
It can be a bitch to get things off but never had a stickabilty problem yet.

Offline blueskydriver

  • I am chained to this website!
  • *
  • Posts: 1,664
  • Karma: +4/-2
  • FSX/FS9 PM, PMDG737-700, FDSMIP/Overhead.etc
  • First Name: John
  • Home Location: WI
Re: First 3D Print HOORAY!
« Reply #7 on: February 12, 2018, 07:45:15 PM »
Hey Trev,

Will you please post some links as to where you purchased the PEI and borosilicate glass?

Thank You,

John
| FSX | FDS-MIP OVRHD SYS CARDS FC1| PM | PMDG 737-700 | UTX | GEX | UT7 | ASE | REX2 | AES | TSR | IS | TOPCAT | AvilaSoft EFB | OC CARDS & OVRHD GAUGES| SIMKITS | SW 3D Lights | FS2CREW2010 | FSXPassengers | Flight1 AE | MATROX TH2GO-D | NTHUSIM | 3-Mits EW230Ust Proj |

Offline paulnd

  • Forum GURU
  • *
  • Posts: 48
  • Karma: +1/-0
  • Aviation Enthusiast
  • First Name: Paul
  • Home Location: London
First 3D Print HOORAY!
« Reply #8 on: February 13, 2018, 05:46:59 AM »
I’ve had good experiences with Printbite even when printing ABS

https://flex3drive.com/printbite/




Sent from my iPhone using Tapatalk Pro

Offline Trevor Hale

  • Administrator
  • I am chained to this website!
  • *
  • Posts: 3,551
  • Karma: +22/-0
    • Cockpitbuilders.com
  • First Name: Trevor
  • Home Location: New Liskeard, Ontario
Re: First 3D Print HOORAY!
« Reply #9 on: February 13, 2018, 06:18:01 AM »
Hey Trev,

Will you please post some links as to where you purchased the PEI and borosilicate glass?

Thank You,

John

Here is the Glass, (Fits Perfect)
https://www.amazon.ca/gp/product/B075JKCMRV/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
Its a tempered Glass, not "PyREX" (Borosilicate) But the product is exactly what I wanted.  It almost is like a fibreglass Plate. 

Here is My PEI Sheet, which is a touch small, Should have got it a bit bigger.  When it gets all scratched up and gouged, I will get a bigger one.
https://www.amazon.ca/gp/product/B07765TZ8K/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

Trevor Hale

Owner
http://www.cockpitbuilders.com

Director of Operations
Worldflight Team USA
http://www.worldflightusa.com

VATSIM:

Offline blueskydriver

  • I am chained to this website!
  • *
  • Posts: 1,664
  • Karma: +4/-2
  • FSX/FS9 PM, PMDG737-700, FDSMIP/Overhead.etc
  • First Name: John
  • Home Location: WI
Re: First 3D Print HOORAY!
« Reply #10 on: February 13, 2018, 08:03:43 AM »
Thank you very much Trevor...you're assume!

John
| FSX | FDS-MIP OVRHD SYS CARDS FC1| PM | PMDG 737-700 | UTX | GEX | UT7 | ASE | REX2 | AES | TSR | IS | TOPCAT | AvilaSoft EFB | OC CARDS & OVRHD GAUGES| SIMKITS | SW 3D Lights | FS2CREW2010 | FSXPassengers | Flight1 AE | MATROX TH2GO-D | NTHUSIM | 3-Mits EW230Ust Proj |

 

COUNTDOWN TO WF2018


WORLDFLIGHT TEAM USA

Will Depart in...

Recent Posts

737 seat
by mdavenport
[Today at 06:35:16 AM]
NO HAN ENVIADO LA SERIAL KEY
by a320kH
[Today at 05:56:40 AM]
I Haven´t received the Key Code after I´ve bought it by internet, the iStation
by a320kH
[Today at 05:53:54 AM]
Memphis 727 Build
by navymustang
[Today at 01:55:07 AM]
What have you done for your simulator today?
by blueskydriver
[Today at 01:19:46 AM]
My project, 737 in the basement.
by Goteborg
[August 13, 2018, 06:01:37 AM]
My 737 Desktop Cockpit
by Nolatron
[August 11, 2018, 11:32:17 PM]
Monitor setup - mixing screen sizes
by mdavenport
[August 11, 2018, 06:37:18 PM]
Wanted! Real Boeing 737 TQ
by Philip
[August 11, 2018, 01:23:21 PM]
Mickey's Flightdeck - A Boeing 737-800 Cockpit on Youtube
by Extraterra
[August 10, 2018, 06:27:19 PM]
Boeing light gray paint color
by bernard S
[August 10, 2018, 12:05:45 PM]
727 Builder Intro
by skyline223
[August 10, 2018, 10:52:43 AM]
737-800 Arduino X-Plane Build
by kurt-olsson
[August 09, 2018, 04:45:16 PM]
Move Project Magenta From FSX to P3D Full cockpit
by ScottThePilot
[August 09, 2018, 12:54:14 AM]
The eagle has landed
by simlady/ Karen
[August 08, 2018, 09:08:18 PM]
Need Information on World Flight 2018
by simlady/ Karen
[August 08, 2018, 09:05:36 PM]
Honeywell OEM Overhead Toggle Switch Caps - Replacement Instructions & Part Nos.
by mickc
[August 08, 2018, 03:25:09 AM]
Wanted Pair of Headrests of this type!
by mgovernali
[August 06, 2018, 03:58:03 PM]
FOR SALE - Precision Flight Controls Cirrus II and Remote Instrument Console USB
by XOrionFE
[August 06, 2018, 12:17:59 PM]
737 Overhead and Flaps Gauges For Sale
by navymustang
[August 06, 2018, 10:11:05 AM]
Ozsim International Airlines Goes 4K
by tennyson
[August 05, 2018, 05:31:18 AM]
X-Plane 737-800 Build
by Steenos
[August 03, 2018, 08:23:11 PM]
Teensy joystick quits after calibrated in X-Plane
by kurt-olsson
[August 02, 2018, 06:46:48 PM]
Zibo Flaps dataref
by RayS
[August 02, 2018, 03:57:09 PM]
737NG Simulator DOWN!
by B737NG
[August 01, 2018, 11:39:45 AM]
SOLD: 737NG manuals (FCOM / QRH and more)
by Gallie
[July 31, 2018, 05:43:58 AM]
SOLD: Eros oxygen mask + box
by Gallie
[July 31, 2018, 05:41:09 AM]
CPFlight MIP board
by fsaviator
[July 30, 2018, 11:48:17 PM]
"Cockpit Builders Members Labor Day Weekend Check-In"
by blueskydriver
[July 30, 2018, 11:19:01 PM]
Monitors dvi, vga , hdmi splitter jungle...
by kurt-olsson
[July 29, 2018, 10:39:21 AM]