Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 1
  • *Guests: 42
  • *Total: 43

Our Discord

WORLDFLIGHT 2018 - TEAM USA SUPPORTERS (HERO'S)


We would like to thank our HERO'S for Donating to support WORLDFLIGHT Team USA - 2018

-Sam LLorca, Fred Kurasiewicz, Ray Sotkiewicz, Warren Soeldner  -
  -
Kyle Hathaway, John Miller, John Combs, Karen Combs, Mick Cliffe, John Ziegler, Vincent Thomas -
- Roy Stewart, Joe Lavery, Dr. Steve Eisenberg, Les Barwick, Doug Snow, Greg Hembree -
- James Williams, Edwin Burton Jasper Koelewijn, James Twomey, John Skibo, Trevor Hale -

- Jason Garrett, Scott Wegner, Frank Radl, Ryan O'Keefe, David Bullock, Bob Reed, Don Emersoln, Lisa Lopez-Floriano -
- Shawn Hathaway, Jason Lohrenz, James Reilly, William McSwain David Otey, Mike Sherick -


Ruscool Electronics Intercom #1 - Won by GyverX
Ruscool Electronics Intercom #2 - Won by dj_Boelie
Ruscool Electronics Intercom #3 -Ryan O'Keefe
Geetech A10 3D printer - James Twomey

Thanks to all of you, You all made Worldflight 2018 a success..
Because of all you wonderful people we raised a total of:

$4,100.00 USD


Author Topic: 737-800 Arduino X-Plane Build  (Read 85723 times)

Offline navymustang

  • Simulation Engineer
  • Forum GURU
  • *
  • Posts: 447
  • Building a 737-800 full scale cockpit
  • First Name: Jim
  • Home Location: KMCO
Re: 737-800 Arduino X-Plane Build
« Reply #550 on: October 26, 2018, 08:56:52 PM »
Building a full scale 737-800 AATD for home use. Majority of hardware is from Sismo Solutions, software is Prosim under P3D. An AOPA member and LifeTime member of National Association of Flight Instructors
Please note that I am a self-employed professional cockpit builder that provides consulting to defense contractors and civilian schools and airlines.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #551 on: October 29, 2018, 04:49:07 PM »
Progress on window heat panel

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #552 on: November 05, 2018, 04:34:33 PM »
Could not let go of what Jim told me about the circuit breaker wall. My posts was in the wrong place so i moved them to where the door should be.

Otherwise, motivation really low.

Perhaps there will be some custom J-rails installed before the year ends. (In one seat at least)

Next will be working on the sidewalls... yikes.. woodwork... :(

Offline navymustang

  • Simulation Engineer
  • Forum GURU
  • *
  • Posts: 447
  • Building a 737-800 full scale cockpit
  • First Name: Jim
  • Home Location: KMCO
Re: 737-800 Arduino X-Plane Build
« Reply #553 on: November 05, 2018, 06:55:58 PM »
Looking good !
Building a full scale 737-800 AATD for home use. Majority of hardware is from Sismo Solutions, software is Prosim under P3D. An AOPA member and LifeTime member of National Association of Flight Instructors
Please note that I am a self-employed professional cockpit builder that provides consulting to defense contractors and civilian schools and airlines.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #554 on: November 07, 2018, 01:58:21 AM »
Has anyone tried to move the lockingpin lever 3-5cm more to the inside sucessfully?

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #555 on: November 07, 2018, 04:36:58 AM »
You should be able to do it, the block that the pin slides in will need to be moved across the frame, and will need  threaded inserts installed into the frame as it is hollow.  the arm can be relocated on the shaft and new hole drilled through it for the bolt.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #556 on: November 07, 2018, 08:42:27 AM »
This is excellent news! Custom J-rails is on the way. Just as long i can slide the locking levers 3-5 cm on the shaft i should be able to build something that will hold the pin itself and fit the J-rails.
I really like the original rails-design and not the one where you attach the seat to a plate that moves on the rails. I will have custom boogies created aswell. (Hopefully)

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #557 on: November 12, 2018, 02:02:33 PM »
Thanks to Archen here on the forums and my collaboration this project will gain momentum!

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #558 on: November 12, 2018, 04:30:13 PM »

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #559 on: November 12, 2018, 11:42:21 PM »
Nice job Peter!

Have you put any thought into how to drive the type 2 Korrys with the grey end blocks?

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #560 on: November 13, 2018, 01:26:15 AM »
Which one do you mean Mick? Where are they located inthe cockpit?

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #561 on: November 13, 2018, 02:51:16 AM »
There's a few around the overhead panels, like the APU/Bus panel.  They use positive to activate, instead of ground.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #562 on: November 13, 2018, 04:05:02 AM »
No plan for it right now, will see what i have to come up with. =)

But i can think of one, use spare korrys and switch the caps to a korry 318 and mount that instead so it all fits to my PCB.
Use the front, but replace the back so to say.
« Last Edit: November 13, 2018, 04:24:09 AM by kurt-olsson »

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #563 on: November 13, 2018, 05:52:37 AM »
Rodger!

I did the 4 type 2 ones in my fire panel with small relays that i took from a gutted ACP, but i have almost 25 to work with in the overheads.  Remember the type 1 end caps do not mate with the type 2 bodies, so you may need to get creative with the keyways ;)

I have some I/O boards that you can select ground or supply side switching with in banks of 8, so I will probably use those for the ones i need.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #564 on: November 14, 2018, 04:16:52 PM »
Back online with one panel using the new PCB. Great to get rid of the 5V mess...

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #565 on: November 18, 2018, 01:29:10 PM »
Home made power busses! :)

Offline Steenos

  • Forum GURU
  • *
  • Posts: 100
  • Aviation Enthusiast
  • First Name: Justin
  • Home Location: KCHA
Re: 737-800 Arduino X-Plane Build
« Reply #566 on: November 18, 2018, 06:06:43 PM »
Kurt, you are killing it! I wish I hadn't had to sell all my stuff but I'm going to work at KBOS tower next year :)

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #567 on: November 18, 2018, 08:48:17 PM »
Home made power busses! :)

I might suggest something a bit more protected than that...  it would only take a dropped screwdriver/spanner even a screw to short those plates and take out your power supply or worse.
Have a look at marine bus bars for a cheap and safe alternative, worst case, cut a plastic cover out and mount it on top of at least the positive bars.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #568 on: November 19, 2018, 01:26:27 AM »
Totally agree with you mick. I am in the making of acrylic top covers that will be mounted ontop of the plates.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #569 on: November 19, 2018, 01:36:23 AM »
Kurt, you are killing it! I wish I hadn't had to sell all my stuff but I'm going to work at KBOS tower next year :)

Thanks! Work and family first! 😊

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #570 on: November 19, 2018, 01:53:00 PM »
Yikes!
LED amongs OEM lightning... disgusting...

I will give it a try with some black film to cover the led up and then turn down the brightness by 70%.
If i cant cover up the plastic strip with some film or glas cover, i will remove it.

Really disappointing in both look and feel.


Offline navymustang

  • Simulation Engineer
  • Forum GURU
  • *
  • Posts: 447
  • Building a 737-800 full scale cockpit
  • First Name: Jim
  • Home Location: KMCO
Re: 737-800 Arduino X-Plane Build
« Reply #571 on: November 19, 2018, 06:15:50 PM »
I think almost everyone here has used this technique to light up the MCP. I bet once you connect to the lower panel dimmers you will really like the effect.
Building a full scale 737-800 AATD for home use. Majority of hardware is from Sismo Solutions, software is Prosim under P3D. An AOPA member and LifeTime member of National Association of Flight Instructors
Please note that I am a self-employed professional cockpit builder that provides consulting to defense contractors and civilian schools and airlines.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #572 on: November 20, 2018, 02:39:39 AM »
Will try to add some diffuser, i dont like when you see the dotted led lights.

Hope they are really slim, i would like to integrate it to my MCP lip.

Offline mickc

  • I may as well be Staff!
  • *
  • Posts: 501
  • Aviation Enthusiast
  • First Name: Mick
  • Home Location: VIC, AU
Re: 737-800 Arduino X-Plane Build
« Reply #573 on: November 20, 2018, 07:28:43 AM »
Protip:

1:Use Warm white LED strips, use the higher density 600 leds per 5m stuff
2:Use a proper mounting channel, this can be recessed into the glareshield etc and also has a diffuser built in.  like this one: http://lightingmatters.com.au/wp/shop/slim-recess-line-led-strip-mounting-profile/
3:put a strip of lighting filter material between the LED strip and the diffuser.  I used Lee filters 022 dark amber.

this will correct the light color, and remove the dot effect of the leds.

Offline kurt-olsson

  • I am chained to this website!
  • *
  • Posts: 1,082
  • 737 -mixed year OEM panel builder.
  • First Name: Peter
  • Home Location: Gothenburg
Re: 737-800 Arduino X-Plane Build
« Reply #574 on: November 20, 2018, 08:46:30 AM »
Just bought this:
https://ledsale.se/infalld-mini-led-aluminiumprofil.html?utm_source=google&utm_medium=cpc&utm_campaign=pla&gclid=Cj0KCQiA_s7fBRDrARIsAGEvF8Qjzh2DRnb5G8MOBh1P06RO8sIdN8BpuUT0tekJ815JAn6fdK-LjT8aAn3YEALw_wcB

Any tip on how to drill/make a channel for the strip to be installed in.

Make a line and draw lots of holes?

Problem is that my MDF is 8mm thick and this needs 6mm for installation.


 

COUNTDOWN TO WF2019


WORLDFLIGHT TEAM USA

Will Depart in...

Recent Posts

New Paint for N38AK
by Trevor Hale
[Today at 09:02:53 AM]
boeing overhead circuit breaker back light panel wiring
by jackpilot
[Today at 08:44:05 AM]
Problems with Wideview or Wide Traffic with Pre3DV3
by ZK CWD
[November 20, 2018, 08:46:05 PM]
The Progression of a build [Phase One]
by GyverX
[November 20, 2018, 05:03:33 PM]
For sale! B737 home cockpit - mostly OEM parts!
by Flightdeck57
[November 20, 2018, 01:30:16 PM]
B737 MIP and Overhead gauges
by csp
[November 20, 2018, 10:25:31 AM]
737-800 Arduino X-Plane Build
by kurt-olsson
[November 20, 2018, 08:46:30 AM]
What have you done for your simulator today?
by navymustang
[November 19, 2018, 06:14:09 PM]
Boeing 737-800 NG Wet Compass -1:1 Replica (P3D, Xplane, FSX)
by Reensel
[November 19, 2018, 04:04:32 PM]
Goflight 166 radios and power issue
by Steenos
[November 19, 2018, 12:44:19 PM]
Join me on Vatsim Tonight
by Trevor Hale
[November 18, 2018, 02:00:41 PM]
Mickey's Flightdeck - A Boeing 737-800 Cockpit on Youtube
by Extraterra
[November 18, 2018, 07:54:30 AM]
WARNING do not trade with Flyengravity
by fairchild
[November 17, 2018, 12:35:28 PM]
95% finished Diamond DA62 build
by Bob Reed
[November 17, 2018, 09:19:13 AM]
P3dV4 install to F:
by Ed
[November 17, 2018, 06:54:54 AM]
6 Years already
by blueskydriver
[November 16, 2018, 03:02:47 PM]
For Sale Saitek modules, Commercial Package, Rrice Reduce
by fairchild
[November 16, 2018, 01:10:09 PM]
CockpitSimParts 737 MIP & FWD OVH
by Bob Reed
[November 16, 2018, 10:09:42 AM]
Updating Navigraph FMC Data - Project Magenta / ProSim
by Bob Reed
[November 16, 2018, 09:39:55 AM]
New supplier for your sim
by Fcoq
[November 15, 2018, 07:34:05 PM]
Honeywell 737 ISDU Unit - Pinout for Canon Plugs
by mickc
[November 15, 2018, 06:12:59 PM]
Notice to those who won the intercoms from Ruscool during Worldflight 2018
by RayS
[November 14, 2018, 06:28:58 PM]
B737 Desktop sim project
by archen
[November 14, 2018, 03:48:11 PM]
Keep losing both engines and all power. Help
by mdavenport
[November 13, 2018, 04:15:35 PM]
For Sale-Real Cockpit Gauges...
by blueskydriver
[November 12, 2018, 09:16:00 PM]
For Sale GoFlight Jet Console, 2 Private Pilot Racks all with GoFlight Modules.
by blueskydriver
[November 12, 2018, 09:09:08 PM]
Rudder trim
by Mach7
[November 12, 2018, 07:54:17 AM]
WorldFlight - CockpitBuilders DAL209 Progress
by Trevor Hale
[November 11, 2018, 11:32:12 AM]
WorldFlight - CockpitBuilders UAL1120 Progress
by dougsnow
[November 11, 2018, 11:08:19 AM]
CP Flight Selcal - How does it work
by ZK CWD
[November 10, 2018, 11:51:31 PM]