Ok, here it is the MCP ini file.
APBankFactor= 85
APPitchFactor= 30
These are the settings I have been slowly tinkering with to get my aircraft to fly as desired. APBankFactor= 85 is the one I have worked with the most. In my sim it works backwards to how I thought it worked. I set it to 30 and the aircraft was much worse. So then I took it to 75 and that was much better. I have slowly taken it up to 85. I am very happy with how it works now.
So here is the rest of the ini
[Project Magenta MCP]
Build#519
[Display]
Title=On
Menu=Off
WindowName=MCP (Active) Press Ctrl-L for Logger, Esc For Menu
Topmost=Off
FSWindow=Off
Minimized=On
/ Starts up minimized
NoMinimize=Off
/ Doesn't minimize MCP on double-click
[User]
Log=Off
SerialLog=Off
/ To log the serial communication
CycleMilliSeconds= 40
/ Speed of the MCP cycle, ideally
/ set to 50-70 ms
Top= 0
Left= 0
/ Top/Left coordinates of the MCP
/ program
Width737= 15495
Height737= 2490
Width747= 15390
Height747= 3120
Width777= 15390
Height777= 3150
/ Heigth and width of MCP for the
/ various types
MCPType=737
Intervent737=On
/ Enables SPD intervention buttons
/ for the 737
ClassicEFISSel=Off
/ When set to On, ND modes are selected
/ with the old method, when set to
/ Off, 8 modes are selectable...
/ APP/VOR/MAP/PLN ARC and CTR
DelayMouseClick=On
/ if mouse reaction is too fast,
/ you can delay it setting this flag
/ to On
Font=mcpfont
FontFactor= 1.27
[VNAV]
DescentSpeedControl=On
/ when set to off, pilot controls
/ speed with the throttle
[Aircraft]
[PM BOEING 737-800 ALASKA AIRLINES SPIRT OF SEATTLE1]
[\\FSX-PC\LOCKHEED MARTIN\PREPAR3D V4\SIMOBJECTS\AIRPLANES\PROJECT MAGENTA 738\PMX737-800.AIR]
MinIAS= 0
/ Minimum selectable airspeed
DefaultIAS= 110
DefaultAltitude= 10000
/ Default Speed and Altitude select
/ on startup
AutoHDG=On
AutoVS=On
/ Will automatically select the current
/ HDG and V/S when mode is engaged
MachAltitude= 0
/ Will automatically switch to MACH/IAS
/ when this altitude is crossed (e.g.
/ 23450), 0 disables
AutoCRS=Off
/ When set to ON, VOR/LOC will *not*
/ go into intercept ARM mode first
AllowStabTrimOverride=Off
StabTrimDeflect= 6000
/ Disconnects A/P when Elevator or
/ Aileron is moved more than the
/ deflection value (default 6000)
/ This option needs to be enabled
/ via bit13 offset 0x50A - monitor
/ bit13 0x5528 for current setting
StabTrimOverrideActive=Off
/ This sets the option above to always
/ be active
Rollout=On
/ MCP will steer the aircraft during
/ the rollout phase after an autoland
DisableAdd20Kts=On
/ Will not add 20 Kts to speed during
/ TOGA if set to On
AllowAPOnGround=On
/ Allows engaging AP on the ground
NoModeAfterTOGA=On
/ Doesn't automatically enable FLCH
/ after TOGA mode
UsePanel=Off
/ Set to On if the FS panel or remote
/ programs are used for MCP interaction
PushButton=Off
/ Enables the use of the pushbutton
/ for SPD, ALT and HDG
SpeedProtect=Off
/ Enables speed protection for A/P
/ modes
SELCurrentSpeed=On
/ MCP will take the current speed
/ when any speed mode is engaged
/ for the first time
TerrAlt=Off
/ Alternate Terrain Mode
Flare= 50
/ Altitude above ground at which
/ the flare is initiated during autoland
N1ref= 99.6
N1TOref= 99.6
N1GAref= 90
N1CLBref= 93
N1CRZref= 97.1
ThrRedAlt= 1500
/ Defaults used for reference thrust
/ and thrust reduction altitudes,
/ only if no CDU detected
MaxROC= 9000
MaxROD= 9000
/ Maximum rate of climb/descent
ClimbThrustLimiter=Off
/ Limits the climb thrust increase
/ if the speed increases too much
/ during FLCH/LVLCHNG climbs
Climb2000Spd=Off
/ Climbs with SPD mode during FLCH/LVLCHNG
/ of less than 2400 ft
FlightIdle= 10
ApproachIdle= 15
/ Min Idle Value for Flight/Approach
/ (default 10% and 15%)
UsePMAutobrakes=Off
/ Enables the PM Auto Brake, do not
/ use the FS autobrake system at
/ the same time
DisableAutobrakes=Off
/ Switches Off Autobrakes below 30
/ Knots, both for PM and FS AutoBrake
/ System
DisableBrakes=Off
/ Disables the writing of any brake
/ valuesof the MCP for Rollout -
/ this is *not* the Aurobrake System,
/ if you use PM autobrake, then this
/ has to be off
BrakeFactor= 100
/ Brake factor in percent, default
/ 100%
BrkDiscPark=On
/ Brakes disconnect Parking Brake
ParkNeedsBrk=Off
/ Parking Brake Needs Brakes to be
/ Pressed to engage
TrimMin=-1
TrimCtr= 0
TrimMax= 10
/ 737 Trim Gauge Min/Ctr/Max
UsepmNavSounds=On
/ Will not write Nav Sound flags
/ to FS Offsets but to Project Magenta
/ Offsets
StbySets1200=Off
/ Will set transponder to 1200 when
/ standby is selected
SwapCRS=Off
/ Swaps CRS 1 and CRS 2
[Input]
MouseWheel=On
MouseWheelInvert=On
/ Allows you to 'turn the knobs'
/ of the MCP using the mouse wheel,
/ you can also invert the direction
FSBusWriteBack=Off
/ Will write back Speed and V/S values
/ to offsets 0x5406 and 0x540C respectively
[Autopilot]
APProjectMagenta=On
/ Enables the PM autopilot and overrides
/ the FS autopilot
APBankFactor= 85
APPitchFactor= 30
/ Autopilot pitch and bank factors,
/ the higher the value, the larger
/ the corrections
DynamicPitch=On
/ Enables the PM autopilot and overrides
/ the FS autopilot
DynamicUseLoHi=Off
DynamicPitchLow= 5
DynamicPitchHigh= 19
/ Dynamic pitch will use low (close
/ to 100kts) and high (close to 350
/ kts) values
DynamicPitchTAS=Off
/ Currently Disabled
AltAcqDiv= 4
/ Altitude Divisor VS/this = capture
/ alt difference
/ Project Magenta Autopilot for Pitch
/ and Bank modes
[Hardware Connections]
/ Enter Comm port the device is connected
/ to, please do not use this if you
/ do not have any hardware connected
/ e.g. enter = 2 for COM2:
/ Precision Flight Controls MCP hardware
/
www.flypfc.comPFCComm= 1
PFC9600=Off
/ Important, the PFC9600 flag should
/ be set to OFF for normal use, currently
/ it is just for testing purposes
CautionThroughPass=Off
/ PFC Caution Button pressed are
/ not handled, but passed through
/ to 0x5534
/ For CPFlight 737 MCP hardware
www.cpflight.com ForceHardwareLight=Off
UseInstLight=Off
IgnoreBattery=Off
/ Ignores pmSystems battery and FS
/ Avionics (Battery)
IgnoreAvionics=On
/ Ignores only FS Avionics (Battery)
DisableFSMessage=Off
/ Disables sending messages to FS
/ Window
NoMenu=Off
/ Removes Menu access and close button
PauseMetric=Off
/ First Officer Meters Pushbutton
/ sets Pause
CargoReset=Off
/ Cargo Buttons used for FS reset
/ via Instructor Station (CP Center
/ Console only)
CargoPause=On
/ Cargo Button used for FS Pause
/ (CP Center Console only)
CPFlightIP=
CPFlightPort= 0
/ CP Flight IP Address and IP Port
/ (default 4500)
CPFlightComm= 0
/ CP Flight Comm Port
CPFlightIO=On
/ Set CPFlightIO=Off to *disable*
/ digital and analog input/output
DisableMIP=Off
/ Set DisableMIP *disable* CPFlight
/ MIP handling (e.g 737 sixpack troubleshooting)
/ For FDS G1 Hardware Communication
FDS_G1_Comm= 0
/ Flight Deck Solutions FDS Glare
/ On/Off
FDSGlare=Off
/ For Daken IFS Hardware
DakenSkys_IFS_Comm= 0
/ FSC MIP Hardware
FSCMIPComm= 0
FSCMIPInvertGear=Off
/Inverts Gear Direction
FSCMIPInvertSixPack=Off
/Inverts both Sixpack Anunciation Lines
/ FSC Throttle Hardware Comm
/
http://www.flightsimulatorcenter.com FSCThrottleQuadrantComm= 0
FSCNOTMotorized=On
FSCTQMotorDisable=Off
/Disables the motorization of the throttle
FSCTQTrimMotorDisable=Off
/Disables the motorization of the trim
FSCTQTrimSpeed= 30
/Sets trim motor speed 0 min 255 max (default 30)
FSCTQInvertTrim=On
/Inverts Trim Motor Direction
FSCTQInvertTrimWheel=Off
/Inverts Trim Wheel Direction (when stab trim disconnected
FSCTQTrimOffset0= 177
FSCTQTrimOffset10= 88
/Offsets Trim Indicator for Trim 0 and Trim 10
FSCTQInvertSpoiler=On
/Inverts Spoiler Potentiometer Direction
FSCTQInvertSpoilerMotor=Off
/Inverts Spoiler Motor Direction
FSCTQCalib= 0
/UnCalibrated=0 - Calibrated=1 - Mixed=2 - Diff=3 - 2SameAs1=4 - useAdjust=5
FSCTQAdjust= 0
/Adjusts Throttle 2 position by X
FSCSplArmPos= 212
/Sets Spoiler Arm Position
FSCRevPct= 15
/Travel of reversers before they are activated, min 15%, default 35%
FSCThrottle1Min= 19
FSCThrottle1Mid= 0
FSCThrottle1Max= 155
FSCThrottle2Min= 19
FSCThrottle2Mid= 0
FSCThrottle2Max= 148
FSCReverser1Min= 0
FSCReverser1Max= 82
FSCReverser2Min= 0
FSCReverser2Max= 84
FSCSpoilerMax= 199
FSCSpoilerMin= 15
FSCSingleThrottle= 0
FSCSingleReverser= 0
FSCThrIntervent=On
FSCTQMotBuffer= 13
/ Top and Bottom Buffer zone to switch
/ off Throttle Motors (default 13)
/ FSC Throttle Hardware Ver 0
/ Cockpitsonic EHID
/
http://www.cockpitsonic.com EHIDComm=Off
/ Can be set to 'On', 'Off', 'localhost'
/ or IP Address
/ ELAN MCP hardware
ElanComm= 0
ElanBaudRate=
/ Please leave ElanBaudrate empty
/ unless you know what you are doing(!)
/ Aerosoft 747 MCP hardware
www.mcp747.com AerosoftComm= 0
AerosoftFPV= 14
AerosoftDHRST= 0
/ Defines the action (offset 0x4F4)
/ of the Aerosoft FPV button or DH
/ Reset button, e.g. 14=FPV, 6=CTR
/EicasButton1=???
/ You can define the action (offset
/ 0x4F4) of each of the 10 EICAS
/ buttons by setting the corresponding
/ value here (e.g. EicasButton1=71,
/ EicasButton10=87)
[EPIC]
DisableRemoteMCP=Off
/ Set to on to disable input from
/ other programs using these offsets
/ via FSUIPC
/ Syntax: input type = joystick,
/ axis
[Extra]
NoFSCOptions=Off