Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 0
  • *Guests: 12
  • *Total: 12

Our Discord

Author Topic: SIOC Stepper Help  (Read 610 times)

Offline okansacli

  • CockpitBuilder
  • *
  • Posts: 6
  • Aviation Enthusiast
  • First Name: Okan
  • Home Location: LTBA
SIOC Stepper Help
« on: September 04, 2018, 12:31:02 AM »
Hello

I am building a wet compass with a step motor using the Open Cockpits Stepper Motor Card.

I have no issues with the SIOC code.

And I believe to have achieved the optical sensor working correctly (no needle in between +5vdc, needle in between 0vdc in the middle pin of the 3pin position group)


I can not seem to run the iostepper.exe correctly as always I see C.Motor1,2 and 3 to be 0 with a continousluy rotating step motor.


Any suggestions ? Did anyone else experience similar issues with open cockpit step motor calibration ?


Best Regard from Istanbul


Okan




Offline iwik

  • Forum GURU
  • *
  • Posts: 365
  • GA Jockey
  • First Name: Les
  • Home Location: Christchurch New Zealand
Re: SIOC Stepper Help
« Reply #1 on: September 04, 2018, 01:00:47 AM »
Okan,
The stepper motor should turn at power up. It should do two revolutions then stop. If it doesnt then the opto fedback is not working. Make sure you have enable the correct motor.
Also when it rotates short out the opto input to the board and it should stop.
Les

Offline okansacli

  • CockpitBuilder
  • *
  • Posts: 6
  • Aviation Enthusiast
  • First Name: Okan
  • Home Location: LTBA
Re: SIOC Stepper Help
« Reply #2 on: September 04, 2018, 02:38:31 AM »
Thank you for the feedback Les,

The stepper motor turns at power up and keeps on turning .. does not stop..

The opto feedback works (i asumme) such that the middle pin (the 3 pin position group) has +5v when the sensor is not blocked, when the sensor is blocked has 0 v.


How can I short our the opto input (shall I bridge pin 2 and pin 3) ?


What do you mean "make sure you enable the correct motor" ? please clarify


Best Regards
« Last Edit: September 04, 2018, 02:39:21 AM by okansacli »

Offline iwik

  • Forum GURU
  • *
  • Posts: 365
  • GA Jockey
  • First Name: Les
  • Home Location: Christchurch New Zealand
Re: SIOC Stepper Help
« Reply #3 on: September 04, 2018, 03:42:17 PM »
Hi,
Pin 1 is 0v and 3 is 5v. Just short pin 1 and 2 together and the motor should stop.
Make sure you  sc the correct pos input for the motor number you are using.
Sorry about the motor enable remark. That shouldnt matter.
I have made the mistake of sc the wrong pos input and wondered why. Just to make sure
try sc any of the motor position inputs. Dont get mixed up with the Analogue inputs on
the board.
Hope this helps.
Les

Offline okansacli

  • CockpitBuilder
  • *
  • Posts: 6
  • Aviation Enthusiast
  • First Name: Okan
  • Home Location: LTBA
Re: SIOC Stepper Help
« Reply #4 on: September 12, 2018, 10:00:11 AM »
the H21A1 type optical sensor was doing its job by switching the 5vdc to 0 vdc when there was an obstruction in between "without" connection to the OC Stepper cards. But when connected to the OC stepper position pins, the voltage drop was limited to ~2vdc instead of 0 vdc (somehow) which made the step connected to the OC stepper to keep on rotating.

So I have changed the optical sensor to LM393 based sensor and it works like a charm. (the sensor was available for audrino as a motor speed sensor)

So for those who plan to use OC stepper card, make sure that the optical position sensor is doing what it should do.

I have uploaded a video on my web site (okansacli.com) for those who are interested.

Best Regards from Istanbul

okan s.

 

FlightSimExpo 2019

FsExpo

COUNTDOWN TO WF2019


WORLDFLIGHT TEAM USA

Will Depart in...

Recent Posts

What have you done for your simulator today?
by bernard S
[Today at 11:35:41 AM]
GSX across networked client visual computers
by tersekie
[Today at 10:41:43 AM]
Piper Aztec PA23-250 (Help Needed)
by n4208t
[Today at 10:26:57 AM]
X-Plane 737-800 Build
by jskibo
[Today at 09:54:50 AM]
Serial Key
by luisgordo
[May 21, 2019, 05:40:44 PM]
Jetmax TQ - motorized it?
by FredK
[May 20, 2019, 07:58:36 AM]
Mickey's Flightdeck - A Boeing 737-800 Cockpit on Youtube
by Extraterra
[May 20, 2019, 02:47:37 AM]
FDS CDU old
by kattz
[May 19, 2019, 01:13:46 PM]
Join me on Vatsim Tonight
by Trevor Hale
[May 15, 2019, 01:58:50 PM]
Gauge circuit
by jackpilot
[May 15, 2019, 01:56:51 PM]
Prosim and RSP TQ interfacing
by jfuenmayor
[May 15, 2019, 08:53:22 AM]
Arduino Mega question Newbie
by Yair1956
[May 15, 2019, 02:23:57 AM]
f18 mfd
by bernard S
[May 14, 2019, 11:15:44 PM]
Multi-Projector color calibration
by fsaviator
[May 13, 2019, 04:32:23 PM]
Immersive Calibration Pro help?
by jskibo
[May 13, 2019, 09:22:00 AM]
KBD03 Keyboard Emulator
by Yair1956
[May 12, 2019, 03:52:05 PM]
5 Position Rotary Spring return Switch
by Yair1956
[May 12, 2019, 03:09:25 PM]
Flyengravity desktop MIP
by patiju
[May 11, 2019, 05:11:05 PM]
Pfd display.
by Patt737
[May 08, 2019, 12:48:32 PM]
Mini Sim
by jskibo
[May 08, 2019, 08:36:28 AM]
F16 Simulator For Sale
by blueskydriver
[May 08, 2019, 12:14:40 AM]
Wanted: Collins Style radios
by jkbarr30
[May 07, 2019, 08:23:32 PM]
Crap! 26V on 5V backlight!
by Steenos
[May 07, 2019, 05:33:46 PM]
Complete 737-800 cockpit - moving sale
by Ed
[May 07, 2019, 08:01:22 AM]
Prosim 737 iOS help
by Aztrucker
[May 06, 2019, 11:56:30 PM]
Fly Elise Warping
by jskibo
[May 06, 2019, 11:14:31 AM]
CPFlight 737 NG MCP Pro and Efis Pro (SOLD)
by patiju
[May 05, 2019, 10:52:46 AM]
Operating System Blues
by 727737Nut
[May 03, 2019, 11:54:35 AM]
FOR SALE - 737 Sim items
by flymo
[May 02, 2019, 07:43:53 AM]
Cpflight MCP737PRO (SOLD)
by archen
[April 30, 2019, 02:07:33 PM]