Cockpit

* User Profile

Welcome, Guest. Please login or register.

Login with username, password and session length

Who's Online

  • *Users: 1
  • *Guests: 57
  • *Total: 58

Our Discord

Author Topic: A friendly FYI on Boeing rudder pedals  (Read 501 times)

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
A friendly FYI on Boeing rudder pedals
« on: June 09, 2019, 11:16:46 AM »
I am installing OEM hardware where I feel it's necessary for my 737-700 sim.  I've been fortunate to get the yokes, columns, and TQ.  I also purchased an entire rudder linkage set as well, wanting the holy grail of linked brakes and pedals, and hardware substantial enough to do control loading on.

Which brings me to my point.

I had many people tell me that "the rudder pedals from the seven-zero thru the seven-four are the same". 

So when I made a purchasing decision on the rudder pedals and linkages from the seven-four, I wasn't too worried.   I knew ahead of time that there were physical differences in the leg adjusters, that the links for the seven three went aft while the seven four went fwd.  Minor differences that could be resolved.

However, when they arrived, they looked BIG.  And they are.  A size 15 shoe with snow boots could fit in the seven four pedals.

And, they are NOT the same pedals as the seven-three.

While all of the linkages for the brakes, adjusters, etc. should work, the seven three is approx 18" or so wide.  The seven four's system is 20" wide.  This is too wide for the seven three footwell box.

So please keep this in mind.

Thx.

Kev

Offline fsaviator

  • I am chained to this website!
  • *
  • Posts: 1,367
  • Aviation Enthusiast
    • Boeing 737 Next Generation Simulator
  • First Name: Warren
  • Home Location: Riverview, Florida
Re: A friendly FYI on Boeing rudder pedals
« Reply #1 on: June 09, 2019, 11:55:05 AM »
I happen to have four 737 rudder pedals.  Just the pedals - if you are interested.
Warren "MTN385"
Florida

http://www.B737NG-SIM.com and https://www.facebook.com/fsaviator on facebook
FSX, Prosim737 Suite, FDS DSTD 2.0 MIP, RevSim Proline TQ, ACE Dual-linked Yokes, Intel 3.5GHz i7-3770K, MSI Z77A-G45, 16GB G.Skill TridentX DDR3-2400, Galaxy GTX670 GC 4GB, OCZ 60GB Vertex 3

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
Re: A friendly FYI on Boeing rudder pedals
« Reply #2 on: June 09, 2019, 07:47:25 PM »
Thank you.

However, I need the vertical tubes as well like attached.  I found these this morning and now need one more set.  The rest of the seven four setup should work fine.

Regards,

Kev

Offline Gallie

  • Forum GURU
  • *
  • Posts: 59
  • Aviation Enthusiast
  • First Name: Mike
Re: A friendly FYI on Boeing rudder pedals
« Reply #3 on: June 10, 2019, 05:19:27 AM »
Hello,

The Pedals themselves are the same on all 70/72/73 and 74 models.

Ive had 747 pedals and linkage in one of my first cockpit builds.

Boeing changed the linkage on the NG. They stopped using the round linkage and started using rectangular linkage. By using the rectangular linkage they got the pedals closer together and created enough room for the wider CDU bay to fit.

Ive had the linkage of my 737-classic rudder system machined in order to fit the replica NG CDU bay.

The same person also shortened the pins that hold the pedals to the linkage.

I think he removed about 10mm from each.
 
Pics included

Michael

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
Re: A friendly FYI on Boeing rudder pedals
« Reply #4 on: June 10, 2019, 03:25:01 PM »
I considered this bit would have had to machine 2" out and there's not enough there to machine away.  Thanks!

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
Re: A friendly FYI on Boeing rudder pedals
« Reply #5 on: June 13, 2019, 08:42:42 PM »
Hello,

The Pedals themselves are the same on all 70/72/73 and 74 models.

Ive had 747 pedals and linkage in one of my first cockpit builds.

Boeing changed the linkage on the NG. They stopped using the round linkage and started using rectangular linkage. By using the rectangular linkage they got the pedals closer together and created enough room for the wider CDU bay to fit.

Ive had the linkage of my 737-classic rudder system machined in order to fit the replica NG CDU bay.

The same person also shortened the pins that hold the pedals to the linkage.

I think he removed about 10mm from each.
 
Pics included

Michael

Hello, Michael,

I received the 737 pedals and linkages today.  No difference in width, sad to say.  But the 747 is 3" shorter in length, meaning that I don't need as deep of a floor for the hardware as the 737 pedals do.

Both the 747 and 737 are 20" across.  So I will sell the 737 pedals and machine down the 747 pedal ends of the vertical links as you did in your photo.  I need 30mm total.  15mm on a side.

Coming soon - pilot and F/O rudder pedals and linkages for sale!

Thanks.

Kev

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
Re: A friendly FYI on Boeing rudder pedals
« Reply #6 on: June 14, 2019, 07:39:24 PM »
Michael, can the linkage pins that the pedals slide onto be shortened?  They seem pretty hollow?

Thanks.

Kevin

Offline Gallie

  • Forum GURU
  • *
  • Posts: 59
  • Aviation Enthusiast
  • First Name: Mike
Re: A friendly FYI on Boeing rudder pedals
« Reply #7 on: June 15, 2019, 07:19:21 AM »
Hello Kevin,

I had all four pins shortened by 10mm (at the end where the thread is located). They can still handle the stress/forces needed. Not sure if you can shorten them any further without loosing structural strenght. Just in case i also had a pair of new pins created (with metric thread), but i never needed them.

10mm gave me more than enough room for the pedals to fit the 50cm space of the MIP frame.
My MIP frame is 151cm wide, 51cm for the CDU bay and 50cm for both FO and CAPT pedals.
A real MIP frame is about 152.5/153cm wide.

I hope you can find someone to do the machining for you. I wasnt able to find a shop willing to do this job for me, they just thought of rediculous prices and lead times to scare me away.
I was lucky to find a retired mechanic with a small machine shop in his shed. He did all the work for me for a really great price. He also helped me by making a few rare UNF sized bolts and even shortening the trim cable drum.

You might also need to dremel a small piece of material away in order to have the full toe brake travel when the pedals are in the full FWD adjusted position. No big deal.
But this is only needed when you will also be using the adjusment (FWD/AFT with crank) mechanism. Not needed if the pedals are in a fixed position.

Hope this helps, let me know if i can help in any way.

Michael

Offline kattz

  • Forum GURU
  • *
  • Posts: 58
  • Aviation Enthusiast
  • First Name: Kevin
  • Home Location: Ohio
Re: A friendly FYI on Boeing rudder pedals
« Reply #8 on: June 15, 2019, 10:36:39 AM »
Extremely helpful, thanks!

 

COUNTDOWN TO WF2019


WORLDFLIGHT TEAM USA

Will Depart in...

Recent Posts

X-Plane 11 multi-monitor & Fly Elise-ng - tuto
by blueskydriver
[July 20, 2019, 05:33:45 AM]
FOR SALE: CA & FO Cockpit Seats with J Rails
by Philip
[July 19, 2019, 04:23:24 PM]
For sale
by TNT
[July 18, 2019, 07:57:29 PM]
For Sale: Dual Linked Rudder Pedals RSP
by Philip
[July 17, 2019, 06:47:22 PM]
737-800 Arduino X-Plane Build
by kurt-olsson
[July 17, 2019, 02:55:53 PM]
Boeing 737 Dual Linked Yokes
by tennyson
[July 16, 2019, 08:59:28 PM]
Flyengravity desktop MIP (SOLD)
by patiju
[July 16, 2019, 02:01:48 PM]
Flight deck solutions FDS-B737NG-PRO-MX- rudder pedal
by Mach7
[July 16, 2019, 04:52:26 AM]
Korry 318 gets hot.
by Joe Lavery
[July 16, 2019, 03:49:14 AM]
What have you done for your simulator today?
by blueskydriver
[July 14, 2019, 10:25:43 AM]
Where to find or how to make this switch guard?
by blueskydriver
[July 13, 2019, 03:46:30 AM]
NIB 747-400 ThrottleTek + FDS CDUs x2 [SOLD]
by blueskydriver
[July 12, 2019, 10:53:12 PM]
FDS 5V IBL Dimmer and Expansion Board / Pokeys 57E (SOLD)
by fsaviator
[July 10, 2019, 08:35:14 PM]
PM MCP.ini Question...
by ScottThePilot
[July 10, 2019, 12:56:38 PM]
Stab Trim Indicator...
by ScottThePilot
[July 09, 2019, 12:56:42 PM]
Teensy LC Throttle Quadrant
by kurt-olsson
[July 08, 2019, 08:09:41 AM]
Multiple Teensys, sketch upload question
by kurt-olsson
[July 08, 2019, 08:05:27 AM]
Anders Simparts - Summer info
by archen
[July 07, 2019, 03:30:31 AM]
Group buy - Oshino OL-2405BP lamps - interested?
by kattz
[July 03, 2019, 09:26:22 PM]
Prosim737 Ver 2 license for sale
by ifeliciano
[July 02, 2019, 09:58:37 AM]
Anyone have this connector and possibly a clamp as well for the yoke?
by mickc
[July 01, 2019, 08:01:04 PM]
Happy Canada Day
by jackpilot
[July 01, 2019, 10:09:40 AM]
MH 370 Article
by FredK
[June 30, 2019, 07:28:41 PM]
Calling any B747 mechs... please help
by kattz
[June 30, 2019, 06:08:50 PM]
International shipping?
by jackpilot
[June 27, 2019, 08:29:07 AM]
Flooring Installed!
by jackpilot
[June 25, 2019, 05:49:57 PM]
How much room between center pedestal and seat?
by jackpilot
[June 25, 2019, 08:19:42 AM]
2020 Microsoft Flight Simulator - new at E3 2019
by blueskydriver
[June 24, 2019, 02:29:16 PM]
How to install DZUS fasteners?
by Buster99
[June 22, 2019, 04:12:34 PM]
Desert Air Spares - Trustworthy?
by kattz
[June 22, 2019, 12:40:51 PM]