Hallo
First, I wish you all a Happy New Year !
The last few weeks I have been very diligent.
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160104%2Ftemp%2Fyuqu3bch.jpg&hash=8a6a30647d3308e4a68e630597535dbe42a91983) (http://www.directupload.net/file/d/4223/yuqu3bch_jpg.htm)
But now, I need some Measures to finish the sidewalls.
I would be glad if you had some information.
1. the cutout for the lighting from the circuit breaker:
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160104%2Ftemp%2Fcz2pew2e.jpg&hash=274324f5f66304223ffe296d73503464a437b018) (http://www.directupload.net/file/d/4223/cz2pew2e_jpg.htm)
2. the center of axis from tiller to make the drilling:
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160104%2Ftemp%2Fg8s9frjf.jpg&hash=9d082258e73b532d6123b9c410f2bf7af1ff5c89) (http://www.directupload.net/file/d/4223/g8s9frjf_jpg.htm)
Thank you, Thomas
Hello Thomas,
I have the dimension for the total tiller height (I do not have distance A in your picture).
The center of the tiller axle is 57.5 cm from the bare cockpit floor.
This was measured from an actual stripped 737-600NG flight deck (see attached picture which is CPT side)
I hope this helps,
Best Regards,
Marc
Hallo Marc, thank you for answer!
57,5cm viewed from insinde looks perhaps a little bit too deep.
Is it possible, to get the measures from inside (the yellow arrows)?
My dimensions from sidewall are approximately +/-1% by the originals.
Thus, I expect a good result from measures from inside.
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160105%2Ftemp%2F25v7j799.jpg&hash=efa49059046a176ec654da31e07ab697a89ce618) (http://www.directupload.net/file/d/4224/25v7j799_jpg.htm)
I envy you for your real cockpits ^^.
only chance for me to get: go to EDFH and dismantle a parket B738 from Rynair....Tony Ryan has enough of them.
"sorry" for the inconvenience, I´ll try as real as possible.
so long, Thomas
Hallo
I want to show you one of my modes of operating if I have no or no real measures.
I only need a good photo with ruler...that's all the help I need, nothing spectacular.
one photo from my HC and one from original
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160108%2Ftemp%2Fd6spwg96.jpg&hash=ae8a46e65cf0657068adb207a1a6b63334cd5a82) (http://www.directupload.net/file/d/4227/d6spwg96_jpg.htm)
moved and adjusted
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160108%2Ftemp%2F9vzh29yj.jpg&hash=4fb4588c10a86064491c5c7b5352b522d8d495a0) (http://www.directupload.net/file/d/4227/9vzh29yj_jpg.htm)
one above the other
(https://www.cockpitbuilders.com/proxy.php?request=http%3A%2F%2Ffs5.directupload.net%2Fimages%2F160108%2Ftemp%2Flgevhomn.jpg&hash=b4523109bf90291d598c809908a7b1ad854c63f4) (http://www.directupload.net/file/d/4227/lgevhomn_jpg.htm)
In this way I am 100% on original.
so, a small photo spared massive work.
thanks to all, who make it possible.
so long, Thomas
If you can wait until next week, I'll take measurements from a real NG.
Hello Thomas,
57,5cm is the correct measurement from the bare floor to the center of the tiller axle.
Measured from real 737-600NG, alas, not mine!
I do not know how this translates to your setup, that is something you will have to compare and adjust as necessary.
HTH, Marc
~57cm is definitly the correct measure.
I now have all what I need to finish the sidewalls.
thanks a lot to all !
the next phase of construction: fill in.
I will keep you up to date.
so long, Thomas